I have broke something

SilverF0x · Post by **SilverF0x** » Tue Feb 28, 2006 6:39 am

Hi to all, yesterday i was trying to make the line out exit for my dc but i was very unlucky...

because everything was working but when i close my dc a screw cut the wire (of ground) and it detach a little part of a circuit..now dc turn on,read cd but nothing appear on the screen and no sound...so if i post the screen of this little part of circuit someone can say me hot to try to repair it?:) Thanks

and sorry for my english, i'm italian

semicolo · Post by **semicolo** » Tue Feb 28, 2006 7:39 am

yeah post anyway, if I can't help someone else will.

ILAMtitan · Post by **ILAMtitan** » Tue Feb 28, 2006 8:54 am

Could you post a picture of the problem, I think i know what you did, but i jsut want to be sure.

SilverF0x · Post by **SilverF0x** » Sun Mar 05, 2006 1:30 pm

Ok tomorrow i will post sorry i went away if someone will solve my problem i will thanks for ever

SilverF0x · Post by **SilverF0x** » Mon Mar 06, 2006 8:03 am

Here i am this is the photo

http://rapidshare.de/files/14832351/Ahia.jpg.html

Green is were circuit is still

grey is where the circuit is go away...

the photo is the back part of the main board

help me

ILAMtitan · Post by **ILAMtitan** » Mon Mar 06, 2006 10:46 am

you can solder a wire onto the green part, and then just run the other end to a known ground.

semicolo · Post by **semicolo** » Mon Mar 06, 2006 10:50 am

well aren't those, just test pads ?
Are they connected to the ground plane ? The picture is rather blurry.
If so you probably just need to connect the via to the ground.

Try scanning the board, you'll get a far better picture.

SilverF0x · Post by **SilverF0x** » Tue Mar 07, 2006 1:11 pm

can you make an example or another ground ?(Maybe with a picture i'm noob)

the scanner is working bad with the mainboard

SilverF0x · Post by **SilverF0x** » Thu Mar 09, 2006 3:20 am

heyy?:)

SilverF0x · Post by **SilverF0x** » Sat Mar 11, 2006 5:10 am

SilverF0x · Post by **SilverF0x** » Sat Mar 11, 2006 5:10 am

SilverF0x · Post by **SilverF0x** » Mon Mar 13, 2006 3:39 am

Can someone help me ? Even in pvt msn plz

SilverF0x · Post by **SilverF0x** » Wed Mar 15, 2006 10:49 am

Hey

i need only to know a good ground point

Matt · Post by **Matt** » Wed Mar 15, 2006 2:42 pm

The metal bits around the mainpoint are grounds, so are the metal bits around the screws

SilverF0x · Post by **SilverF0x** » Wed Mar 15, 2006 4:04 pm

mattthemodder wrote:The metal bits around the mainpoint are grounds, so are the metal bits around the screws

:( I try with a tester and it say that it's just grounded, even with or without wire

semicolo · Post by **semicolo** » Thu Mar 16, 2006 5:42 am

It means the part of circuit that went off wasn't needed, your problem must come from something else.

SilverF0x · Post by **SilverF0x** » Thu Mar 16, 2006 10:30 am

so i am without any hop to see it working again??maybe a short have destroy something??:(:(

semicolo · Post by **semicolo** » Thu Mar 16, 2006 2:00 pm

Check your power supply, it should give 5V, 12V and 3,3V
If it's ok, something is probably destroyed.