Anyone here done the Modem LED mod?
-
- Insane DCEmu
- Posts: 119
- https://www.artistsworkshop.eu/meble-kuchenne-na-wymiar-warszawa-gdzie-zamowic/
- Joined: Fri Jan 17, 2003 3:42 am
- Has thanked: 0
- Been thanked: 0
You know the wires that connect to your motherboard, the ones like HDD LED, Reset, Keylock and so on? Those gauge of wire are just right. Anything smaller and soldering becomes a a pain in the ass. There is plenty of room inside of the modem to solder.
Anyone know if this works with the BBA?
Anyone know if this works with the BBA?
i LiKe PAiN, WHATS YOUR eXCUSe?
Should work with the BBA, as the pinout is the same on the DC side.
Don't take my word for it, a BBA is a lot to waste.
Don't take my word for it, a BBA is a lot to waste.
Orange_Ribbon wrote:It is also the reason why you can't wear tight pants. Damn anal warts.
Millenium Falcon Dreamcast
-
- Somewhat Dumb Knight
- Posts: 3653
- Joined: Tue Oct 12, 2004 2:26 pm
- Has thanked: 0
- Been thanked: 0
- dcmodder
- Psychotic DCEmu
- Posts: 615
- Joined: Mon Jul 05, 2004 8:42 pm
- Location: ks
- Has thanked: 0
- Been thanked: 0
- Contact:
if you have an old controller (from pretty much any console/pc/ whatever) just get the wire from the controller. split the outer casing of the wire and get the smaller wires from inside. that's what i did for a lot of my wire. get a broken controller from a garage sale or from a friend. any where you can find em. spare parts are good to have around.LyingWake wrote:I had a spare extention thing for my PC PSU and I thought I'd go ahead a cut those wires up so I could use them. They were a bit big, and it was really hard to get them soldered on the pins. I need to buy some thinner wire.
-
- DCEmu Super Poster
- Posts: 1342
- Joined: Thu Aug 26, 2004 4:05 am
- Has thanked: 0
- Been thanked: 0
- Contact:
Thanks dcmodder, I cut up a controller and it worked great. My second mod complete, I think the main LED is next (notice how it's not lit up in the picture).
EDIT: After trying to replace the main LED on 2 different controller ports, I still can't get them working. I don't know what the problem is.
EDIT: After trying to replace the main LED on 2 different controller ports, I still can't get them working. I don't know what the problem is.
Last edited by LyingWake on Tue Aug 09, 2005 10:36 pm, edited 1 time in total.
Looks good. Yours shows the same problem as mine. The crack of light on the left side (this picture) of the jack. Ive been thinking of filling mine in, ive used drywall putty and pain before. Worked great and was easy to remove and re-apply when needed.
Whats hooked up in your serial port there?
Whats hooked up in your serial port there?
i LiKe PAiN, WHATS YOUR eXCUSe?
-
- DCEmu Super Poster
- Posts: 1342
- Joined: Thu Aug 26, 2004 4:05 am
- Has thanked: 0
- Been thanked: 0
- Contact:
BTW dcmodder, the image you created is good, but you have the positive and negative switched. I thought it was just me, but then royhubbus did the mod too and he had to flip the LED. So for those that would like to do this mod here's a diagram for the pins:
Last edited by LyingWake on Tue Aug 09, 2005 9:58 pm, edited 1 time in total.